How to reset the drum on a brother printer

How do you fix a drum on a Brother printer?

When you replace the drum unit with a new one, you need to reset the drum counter by completing the following steps:

  1. Make sure the machine is turned on.
  2. Open the front cover.
  3. Press and hold OK for about two seconds to display Drum Unit, and then press OK.
  4. Press the Up arrow key to reset the drum counter.

How do you clear a brother drum error?

If you reset the drum counter during the life of the drum unit currently being used, the remaining drum life will not be displayed accurately.

  1. Make sure that the machine is turned on.
  2. Open the front cover.
  3. Press and hold OK for 2 seconds.
  4. Press the Up arrow key or 1 to reset the drum counter.
  5. Close the front cover.

Why does my Brother printer keep saying replace drum?

Without a chip, your drum unit has no way of being able to associate itself with your Brother printer. As a result, you will get the “Replace Drum” message because your printer thinks that you’ve not installed a drum unit. On the right is a standard toner cartridge with a chip.27 мая 2014 г.

How do you reset the drum on a brother dr420?

Reset DR420 for Brother HL Printer Models

  1. Turn on the printer and replace the drum. Keep the front door open.
  2. Press and hold the Go button for 4 seconds or until all four LEDs light up.
  3. Release the Go button and close the front door.
  4. If the drum light is off, the drum unit is reset.
You might be interested:  What printer is compatible with macbook air

1 мая 2019 г.

How do you fix a printer drum?

First, you will need to remove the old drum and replace it with the new one:

  1. Make sure that the printer is on and open the front cover.
  2. Remove the toner cartridge and drum unit from the machine.
  3. Push down the green lock lever and remove the toner cartridge from the drum unit.
  4. Unpack the new drum unit.

How do I clean the drum on my Brother printer?

Turn the drum unit as shown in the illustration. Make sure that the drum unit gear is on the left side. Turn the edge of the drum unit toward you by hand while looking at surface of the suspected area. Wipe the surface of the drum gently with a dry cotton swab until the mark on the surface comes off.

Do I need to replace the drum on my Brother printer?

The Brother machine will display a ‘Replace Drum’ or ‘Drum Stop’ message when the machine has printed approximately 15,000 pages. The drums should be replaced as a set in order to maintain print quality. Unlike the toner cartridges, the drum change is not automatically detected by the machine when they are replaced.

What happens if I don’t replace printer drum?

Many consumers have the “If it ain’t broke, don’t fix it” mentality. But the replacement of a drum unit is vital to laser printers’ health. A degraded drum unit can cause streaks, smudges, and blank spots on your printed page even if you just inserted a new printer toner.

How do you check the drum life on a Brother printer?

Can I check the remaining life of my Brother machine’s drum?

  1. Press MENU and choose Machine Info. => Drum Life.
  2. Press the OK key. Your Brother machine’s LCD will display the percentage of remaining drum life.
  3. Press the STOP/EXIT key.
You might be interested:  How do i install my canon printer to my computer?

What are the signs that a printer drum needs to be replaced?

  • Blurry Prints. If your printer is churning out blurry pages, it either means that your printer drum is damaged and in need of replacement or that you need new ink toner. …
  • Black Spots. …
  • Poor Print Quality. …
  • Other Signs and Symptoms.

How do I know if my printer drum needs replacing?

Separate drum units last quite a bit longer than a toner cartridge and typically should be replaced after the use of 3-4 toners. Your printer should inform you when it’s time to replace the drum, but you can usually tell your drum is on it’s last legs if you start to see black spots or lines across the page.

How long does a Brother printer drum last?

approximately 15,000 pages

How do you reset the drum counter on a Brother printer DCP 7065dn?

How to reset the drum counter:

  1. Open the front cover of the printer and push “clear” on the printer display.
  2. Confirm you are installing a new drum unit by pressing the up arrow.
  3. “Accepted” should appear on the LCD display, now you are ready to print!

Do printer drums go bad?

Bad Paper. Using paper not intended for laser printers can not only produce lower quality print, it can wear your printer drum out more quickly. If the paper cannot fully remove the toner from the drum, the drum can build up toner residue, which will prevent it from operating properly.

Leave a Reply

Your email address will not be published. Required fields are marked *