Interesting

How to reset replace drum in brother printer

How do I reset my Brother printer after replacing drum?

DO NOT reset the drum counter unless you are replacing the drum unit.

  1. Close the front cover.
  2. Make sure the machine is turned on.
  3. Press. (Settings). …
  4. Press All Settings. …
  5. Choose Machine Info. or Machine Information => Parts Life.
  6. Press and hold Drum or Drum Life until the machine’s display message changes.
  7. Press Yes.
  8. Press.

Why does my Brother printer keep saying replace drum?

Without a chip, your drum unit has no way of being able to associate itself with your Brother printer. As a result, you will get the “Replace Drum” message because your printer thinks that you’ve not installed a drum unit. On the right is a standard toner cartridge with a chip.27 мая 2014 г.

Do I need to replace the drum on my Brother printer?

The Brother machine will display a ‘Replace Drum’ or ‘Drum Stop’ message when the machine has printed approximately 15,000 pages. The drums should be replaced as a set in order to maintain print quality. Unlike the toner cartridges, the drum change is not automatically detected by the machine when they are replaced.

How do you reset the drum on a brother mfc 7460dn?

Just follow the steps below:

  1. With the front cover open, press Clear.
  2. When prompted, press 1 to confirm you are installing a new drum unit.
  3. When the LCD shows Accepted, close the front cover.

20 мая 2015 г.

How do you fix a Brother printer drum?

Remove the toner cartridge and drum unit from the machine. Push down the green lock lever and remove the toner cartridge from the drum unit. Unpack the new drum unit. Click the toner cartridge into the new drum unit until you hear it lock into place.

You might be interested:  How to print from android phone to wireless canon printer

What happens if you don’t replace printer drum?

Many consumers have the “If it ain’t broke, don’t fix it” mentality. But the replacement of a drum unit is vital to laser printers’ health. A degraded drum unit can cause streaks, smudges, and blank spots on your printed page even if you just inserted a new printer toner.

How do I know if my printer drum is bad?

The most obvious is most common on laser color printers and can be detected by a flashing message on the printer display screen. Other signs of a bad printer drum include printing blank pages, printing gray pages and strange sounds coming from the printer as it prints.

How do you clean a Brother printer drum?

Turn the drum unit as shown in the illustration. Make sure that the drum unit gear is on the left side. Turn the edge of the drum unit toward you by hand while looking at surface of the suspected area. Wipe the surface of the drum gently with a dry cotton swab until the mark on the surface comes off.

How long does a Brother printer drum last?

approximately 15,000 pages

How often does a printer drum need to be replaced?

10,000 to 50,000

Can you clean a printer drum?

After you have removed the chunks of toner, dip a cotton swab in rubbing alcohol. Carefully wipe off any dirty areas visible on the drum. If the drum unit is dirty, apply some rubbing alcohol onto your lint-free cloth and carefully wipe the body of the drum unit.

How do I reset my Brother printer?

Press the Up arrow key select Reset.

  1. Press the Settings button.
  2. Press All Settings.
  3. Press Initial Setup.
  4. Press Reset.
  5. Press All Settings or Factory Reset (depends on which model you have).
  6. Press Yes.
  7. Press Yes again and hold for two seconds.
You might be interested:  How to scan printer to computer

How do I reset my Brother MFC 7860dw?

Brother MFC7360N MFC7860DW Toner Counter Reset

  1. Open the front panel of your Brother MFC-7360N or MFC-7860DW Multifunction printer.
  2. Press the Clear/Back button. A display message will then show “REPLACE DRUM? …
  3. Do not type 1 or 2, this is not the command you should enter. …
  4. Close the front door.

Leave a Reply

Your email address will not be published. Required fields are marked *