Interesting

How do you reset the drum on a brother printer

How do I reset my printer drum?

If you reset the drum counter during the life of the drum unit currently being used, the remaining drum life will not be displayed accurately.

  1. Make sure that the machine is turned on.
  2. Open the front cover.
  3. Press and hold OK for 2 seconds.
  4. Press the Up arrow key or 1 to reset the drum counter.
  5. Close the front cover.

How do you fix a drum on a Brother printer?

When you replace the drum unit with a new one, you need to reset the drum counter by completing the following steps:

  1. Make sure the machine is turned on.
  2. Open the front cover.
  3. Press and hold OK for about two seconds to display Drum Unit, and then press OK.
  4. Press the Up arrow key to reset the drum counter.

What does it mean to replace drum on Brother printer?

The Brother machine will display a ‘Replace Drum’ or ‘Drum Stop’ message when the machine has printed approximately 15,000 pages. The drums should be replaced as a set in order to maintain print quality. Unlike the toner cartridges, the drum change is not automatically detected by the machine when they are replaced.

What happens if you don’t replace printer drum?

Many consumers have the “If it ain’t broke, don’t fix it” mentality. But the replacement of a drum unit is vital to laser printers’ health. A degraded drum unit can cause streaks, smudges, and blank spots on your printed page even if you just inserted a new printer toner.

What is the drum on a printer brother?

A drum unit is a green metal cylinder or tube that carries a static electrical charge that attracts the toner powder from the toner cartridge and applies it to the paper as it passes through the printer. Therefore, you will always find that drum unit is located very close to or even attached to the toner cartridge.27 мая 2014 г.

You might be interested:  How to delete a printer from mac

How do I clean the drum on my Brother printer?

Turn the drum unit as shown in the illustration. Make sure that the drum unit gear is on the left side. Turn the edge of the drum unit toward you by hand while looking at surface of the suspected area. Wipe the surface of the drum gently with a dry cotton swab until the mark on the surface comes off.

How do I know if my printer drum is bad?

The most obvious is most common on laser color printers and can be detected by a flashing message on the printer display screen. Other signs of a bad printer drum include printing blank pages, printing gray pages and strange sounds coming from the printer as it prints.

How do I know if my printer drum needs replacing?

Separate drum units last quite a bit longer than a toner cartridge and typically should be replaced after the use of 3-4 toners. Your printer should inform you when it’s time to replace the drum, but you can usually tell your drum is on it’s last legs if you start to see black spots or lines across the page.

How long does a Brother printer drum last?

approximately 15,000 pages

Is a printer drum the same as toner?

The two most important components of a laser printer are the toner cartridge and the drum unit which is where the question of drum units vs. toner cartridges comes in. … So, the toner cartridge is the container that holds toner particles while the drum unit is the component that holds the image that needs to be printed.

You might be interested:  How to connect printer to mobile via usb

How do you check the drum life on a Brother printer?

Can I check the remaining life of my Brother machine’s drum?

  1. Press MENU and choose Machine Info. => Drum Life.
  2. Press the OK key. Your Brother machine’s LCD will display the percentage of remaining drum life.
  3. Press the STOP/EXIT key.

How do I factory reset my Brother MFC l2740dw?

Factory Reset

  1. Press the Up or Down arrow key to select Initial Setup, and then press OK.
  2. Press the Up or Down arrow key to select Reset, and then press OK.
  3. Press the Up or Down arrow key to select Factory Reset, and then press OK.
  4. Press the Up arrow key to select Reset.
  5. Press the Up arrow key to restart the machine.

How do you reset the drum on a MFC l2750dw?

Reset the drum counter

  1. Make sure the machine is turned on.
  2. Close the front cover.
  3. Press (Cancel).
  4. Press and hold (Toner) for five seconds.
  5. Press Drum, and then press Yes.

Leave a Reply

Your email address will not be published. Required fields are marked *